Fuse Failure Indicator Circuit Diagram

Mains/Fuse Failure Indicator Circuit Diagram. The indicator shows when the mains is present at its output by a continuous glow of a neon bulb, La1, and when the fuse is blown by flashing of the neon bulb. When the fuse is intact, capacitor C2 acts as the series resistance for the neon bulb, so that this glows continuously. When the fuse has blow, the mains voltage across diode D1 is applied as a pulsating direct voltage to network R1-C1. Capacitor C1 charges slowly and when the voltage across it reaches 80–100 V, the neon bulb comes on. Capacitor C1 is then discharged slowly via diode D2 and the bulb.

Mains/Fuse Failure Indicator Circuit Diagram

When the voltage across it has dropped sufficiently, the bulb goes out, whereupon C1 slowly charges again. This process repeats itself, so that, provided the values of R1 and C1 are right, the bulb flashes visibly. The potential across capacitor C2 is a ramp with a peak value of 30 V (which is, of course, applied to the load). Note that the neon bulb used for this purpose must not be a type that has a built-in series resistor.The indicator shows when the mains is present at its output by a continuous glow of a neon bulb, La1, and when the fuse is blown by flashing of the neon bulb. When the fuse is intact, capacitor C2 acts as the series resistance for the neon bulb, so that this glows continuously. When the fuse has blow, the mains voltage across diode D1 is applied as a pulsating direct voltage to network R1-C1. Capacitor C1 charges slowly and when the voltage across it reaches 80–100 V, the neon bulb comes on. Capacitor C1 is then discharged slowly via diode D2 and the bulb.

Read More

Power On Indicator Circuit Diagram

Power On Indicator Circuit diagram. Some types of electronic equipment do  not provide any indication that they are  actually on when they are switched on.  This situation can occur when the back-light of a display is switched off. In addition, the otherwise mandatory mains  power  indicator  is  not  required  with  equipment  that  consumes  less  than  10 watts. As a result, you can easily forget  to switch off such equipment. If you want  to know whether equipment is still drawing power from the mains, or if you want  to have an indication that the equipment  is switched on without having to modify the equipment, this circuit provides a solution. 

One way to detect AC power current and  generate a reasonably constant voltage  independent of the load is to connect a  string of diodes wired in reverse parallel in series with one of the AC supply  leads. Here we selected diodes rated  at 6 A that can handle a non-repetitive  peak current of 200 A. The peak current  rating is important in connection with  switch-on  currents.  An  advantage  of  the selected diodes is that their voltage  drop increases at high currents (to 1.2 V  at 6 A). This means that you can roughly  estimate the power consumption from  the brightness of the LED (at very low  power levels). The voltage across the diodes serves as  the supply voltage for the LED driver. To  increase the sensitivity of the circuit, a  cascade circuit (voltage doubler) consisting of C1, D7, D8 and C2 is used to double  the voltage from D1–D6. Another benefit  of this arrangement is that both halve- waves of the AC current are used. We use  Schottky diodes in the cascade circuit to  minimise the voltage losses.

The LED driver is designed to operate the LED  in blinking mode. This increases the amount  of current that can flow though the LED when  it is on, so the brightness is adequate even  with small loads. We chose a duty cycle of pproximately 5 seconds off and 0.5 second  on. If we assume a current of 2 mA for good  brightness with a low-current LED and we can  tolerate a 1-V drop in the supply voltage, the  smoothing capacitor (C2) must have a value of  1000 µF. We use an astable multivibrator built around two transistors to implement a  high-efficiency LED flasher. It is dimensioned to minimise the drive current of  the transistors. The average current consumption is approximately 0.5 mA with a  supply voltage of 3 V (2.7 mA when the  LED is on; 0.2 mA when it is off). C4 and  R4 determine the on time of the LED (0.5  to 0.6 s, depending on the supply volt-age). The LED off time is determined by  C3 and R3 and is slightly less than 5 seconds. The theoretical value is R × C × ln2,  but the actual value differs slightly due to  the low supply voltage and the selected  component values.

 

Diodes D1-D6 do not have to be special  high-voltage diodes; the reverse volt-age is only a couple of volts here due  the reverse-parallel arrangement. This  voltage drop is negligible compared to  the value of the mains voltage. The only  thing you have to pay attention to is the  maximum load. Diodes with a higher  current rating must be used above 1 kW.  In addition, the diodes may require cool-ing at such high power levels.  Measurements on D1–D6 indicate that  the voltage drop across each diode is  approximately 0.4 V at a current of 1 mA.  Our aim was to have the circuit give a  reasonable indication at current levels  of 1 mA and higher, and we succeeded  nicely. However, it is essential to use a  good low-current LED.

Power On Indicator Circuit diagram :

 

Power On Indicator Circuit Diagram

 

Caution: the entire circuit is at AC power potential. Never work on the circuit with the mains cable plugged in. The  best enclosure for the circuit is a small,  translucent box with the same colour as  the LED. Use reliable strain reliefs for the  mains cables entering and leaving the  box (connected to a junction box, for  example). The LED insulation does not  meet the requirements of any defined insulation class, so it must be fitted such that it  cannot be touched, which means it cannot  protrude from the enclosure.

Read More

Isolated Fuse Fail Indicator Circuit Diagram

This circuit uses standard components and shows a method of indicating the fuse status of mains powered equipment while providing electrical isolation from the mains supply.

A standard miniature low power mains transformer  (e.g. with an output of around 6 V at 1.5 VA) is used as a ‘sense’ trans-former with its primary winding (230 V) connected across the equipment’s input fuse so that when the fuse blows, mains voltage is applied to the transformer and a 6 V ac output volt-age appears at the secondary winding. The 1N4148 diode rectifies this voltage and the LED lights to indicate that the fuse has failed. The rectified voltage is now connected to an RC low-pass filter formed by the 10 kΩ resistor and 100 nF capacitor. The resulting positive signal can now be used as an input to an A/D converter or as a digital input to a microcontroller (make sure that the signal level is within the microcontroller input voltage level specification). The 1 MΩ resistor is used to discharge the capacitor if the input impedance of the connected equipment is very high. 

Isolated Fuse Fail Indicator Circuit Diagram

Isolated Fuse Fail Indicator Circuit Diagram

As long as the fuse remains intact it will short out the primary winding of the ‘sense’ transformer so that its secondary out-put is zero.

Read More

Network Voltage Indicator Circuit Diagram

Using this schematic is created a network voltage indicator electronic circuit. If the input voltage is gift across the network, the optocoupler transistor is open, T1 is blocked and controlled rectifier, Th1, is in a very state of conduction. Since each terminals of the piezoelectric buzzer is at identical potential, buzzer is off. If voltage disappears, the transistor T1 enters the conduction and therefore makes the terminal of buzzer to be placed on the bottom (maintains thyristor conduction state).

during this state of affairs, there's a sufficiently giant potential distinction across the buzzer and D5's to see that these 2 components to point AC power loss, each audible and visual. By pressing the reset button current is interrupted by Th1, therefore thyristor enter in blocking state and therefore the different terminal of the buzzer is connected to ground.

Network Voltage Indicator Circuit Diagram

Read More

Flat Battery Indicator Circuit Diagram

This small circuit was developed to monitor the battery in a model hovercraft. The lift in the model is produced by an electric motor driving a fan. To avoid the possibility of discharging the rechargeable battery pack too deeply, the design lights a conspicuous LED mounted on the model when a preset threshold voltage is reached. The circuit only uses a few components, which helps keep the total weight of the model down. The circuit connects to the model only across the two points where the voltage to be monitored can be measured. These also supply power to the circuit.

The best place to connect the circuit is not at the battery terminals, but rather at the motor connections. The circuit is suitable for use with nominal battery voltages of 4.8 V to 9.6 V (four to eight 1.2 V cells). For example, if there are six cells in the battery, its nominal terminal voltage will be 7.2 V. A discharge threshold voltage of around 1 V per cell is appropriate, which means that for six cells the threshold is 6 V. We now need to set the voltage UZ across the adjustable Zener diode D1 (an LM431) to about 0.5 V less than the threshold voltage at which we want LED D2 to light.

Flat Battery Indicator Circuit Diagram




This voltage is controlled by the choice of the value of resistor R1. As indicated in the circuit diagram, this is done with the help of a trimmer potentiometer (R1.A) with a fixed resistor (R1.B) in series. Using the suggested values (10 kΩ for both the potentiometer and the fixed resistor) allows the discharge threshold voltage to be set between about 5.5 V and 8 V. For lower or higher voltages R1.B should be made correspondingly smaller or larger. Once the desired value of UZ has been set the total resistance (R1.A plus R1.B) can be measured and a single fixed-value resistor of this value substituted at R1.

In the example mentioned of a six-cell battery, a voltage of 7.2 V will appear at the emitter of T1 when the battery is charged. At its base is UZ, which should be 5.5 V (6 V – 0.5 V) in the case of a discharge threshold voltage of 6 V. As long as the battery voltage remains at least 0.5 V higher than UZ, T1 will conduct and T2 will block, with the result that LED D2 will not light. If the battery voltage should fall below about 6 V (UZ + 0.5 V), T1 will block, T2 will conduct and LED D2 will light. To ensure stable operation of the circuit R6 provides a small amount of switching hysteresis. By adjusting the resistor value between 100 kΩ and 220 kΩ the amount of hysteresis can be varied.

The current drawn by the circuit itself is less than 5 mA (as measured with a battery voltage of 7.2 V). When the LED lights an additional 10 mA (the LED current) is drawn, for a total of around 15 mA. The adjustable Zener diode can be replaced by a fixed Zener with a voltage 0.5 V less than the desired threshold. Resistors R1 and R2 can then be dispensed with. A flashing LED can be used for D2 (without series resistor R7). An acoustic alarm can be provided by replacing D2 and R7 by a DC buzzer with a suitable operating voltage.

Read More

Check Inductors With This Simple Q Meter

While LCR meters are readily available at reasonable cost, they do not measure the Q of an inductor. This circuit enables you to measure the Q of inductors with the aid of an RF signal generator. A capacitor is connected in parallel with the inductor to form a tuned circuit. By varying the frequency, you can measure the resonance frequency of the tuned circuit and its -3dB bandwidth. The Q is then the resonance frequency divided by the -3dB bandwidth. Transistor Q1 is an emitter follower acting as input buffer to drive RF transformer T1. The secondary winding of T1 then drives the parallel tuned circuit formed by the inductor under test (Lx), T1’s secondary and tuning capacitor VC.

The tuned circuit so formed is buffered by JFET Q2 and transistor Q3 which form a cascode stage with about 3dB of gain. The JFET provides a high impedance so that the loading of the tuned circuit is minimal (note: an MPF102 can be substituted if you cannot obtain a 2N5485). The RF output from Q2's collector can be monitored by an oscilloscope to easily find the point of resonance and read the frequency. Alternatively, the RF output can be read by an external frequency meter. Diodes D1 & D2 and the 5.6nF capacitors form a voltage doubler rectifier to drive a 100µA DC meter so that the resonance can be found (in the absence of an oscilloscope).




Trimpot VR1 provides a sensitivity adjustment for the meter. Transformer T1 is wound on a 12mm diameter ferrite toroid core. The primary winding consists of 50 turns of 0.2mm diameter enamelled copper wire, while the secondary is a single turn consisting of a strip of brass 0.5mm thick and 2.5mm wide bent into a horseshoe shape and threaded through the centre of the toroid. VC is a small AM tuning capacitor with both gangs connected in parallel.

To measure Q, the output of the RF signal generator should be around 0.5V peak. Adjust the frequency until the meter's reading peaks, then adjust VR1 so that the meter reads full scale (100µA). Read the resonance frequency F0 from the frequency scale of the signal generator or better still, the reading on a frequency meter.

Next, increase the signal frequency until the meter reads 70µA and note this frequency as F2. That done, reduce the frequency on the signal generator below the resonance frequency until the meter again reads 70µA and note this frequency as F1. The Q can now be calculated as:

Q = F0/(F2 - F1)

While using a variable tuning capacitor will enable a wider range of inductors to be tested, the main advantage is estimating the distributed capacitance of the inductor as well. To do this, you have to calibrate the tuning scale with a capacitance meter, by measuring the capacitance across the tuning capacitor with no inductor connected. This is done with the unit switched off. Marking off increments of 20pF should be sufficient.

Set the tuning capacitor to say ¼ of its maximum value and note this value as C1. Adjust the RF signal generator frequency so that the inductor under test is at resonance and note this frequency as F0. Now set the RF generator frequency to half F0, adjust the tuning capacitor until resonance and note this capacitance as C2. The distributed capacitance of the inductor is (C2 - 4C1)/3.

Read More

Maximum Minimum Voltage Indicator Circuit Diagram

This circuit indicates which of three voltages in the range from about about -4V to about +4V - at A, B and C - is the highest by lighting one of three indicator LEDs. Alternatively, it can be wired to indicate the lowest of three voltages or to indicate both the highest and lowest voltages. Op amps IC1a, IC1b & IC1c are wired as comparators, while the three indicator LEDs and their series 1kO current limiting resistors are strung across the op amp outputs to implement the appropriate logic functions.

Circuit diagram:

Maximum Minimum Voltage Indicator Circuit Diagram

For example, LED A will light only when pin 8 of IC1c is low (ie, A greater B) and pin 7 of IC1b is high (ie, A greater C). Similarly, LED B will light only when pin 8 of IC1c is high (ie, B greater A) and pin 1 of IC1a is low (ie, B greater C). LED C works in similar fashion if the voltage at C is the highest. Note that if all the LEDs and their parallel 1N4148 diodes are reversed, the circuit will indicate the lowest of the three input voltages. And if each 1N4148 diode is replaced by a LED, the circuit will indicate both the highest and lowest inputs.

Author: Andrew Partridge - Copyright: Silicon Chip

Read More

Advanced Linear NiMH/NiCd Fast Battery Charger

This is a simple Batteries charger for NiMH/NiCd.It Requires No Microcontroller or any Firmware.Linear Technology Corporation introduces the LTC4060, an autonomous 1- to 4-cell, 0.4A to 2A linear NiMH and NiCd battery charger. The LTC4060 includes all the functions required for a battery charger circuit, operating without the aid of a microcontroller or firmware. The design is simple and needs only three passive components. The LTC4060 also eliminates the need for a sense resistor and blocking diode, which increases efficiency and lowers the solution cost. This IC is targeted at applications including portable medical equipment, automotive diagnostic systems and industrial/telecom test devices.

Features

• Complete Fast Charger Controller for Single, 2-, 3- or 4-Series Cell NiMH/NiCd Batteries
• No Firmware or Microcontroller Required
• Termination by –?V, Maximum Voltage or Maximum Time
• No Sense Resistor or Blocking Diode Required
• Automatic Recharge Keeps Batteries Charged
• Programmable Fast Charge Current: 0.4A to 2A
• Accurate Charge Current: ?5% at 2A
• Fast Charge Current Programmable Beyond 2A with External Sense Resistor
• Automatic Detection of Battery
• Precharge for Heavily Discharged Batteries
• Optional Temperature Qualified Charging
• Charge and AC Present Status Outputs Can Drive LED
• Automatic Sleep Mode with Input Supply Removal
• Negligible Battery Drain in Sleep Mode: <1?A
• Manual Shutdown
• Input Supply Range: 4.5V to 10V 

Read More

Indicator for Dynamic Limiter Schematic Diagram

The indicator described here is specifically designed for adjusting the dynamic limiter described elsewhere in this edition and checking whether the maximum level of the reference voltage (P1) needs to be modified. Her e we use a 4 -to -16 decoder IC (type 4514) to monitor the state of the four-bit up/down counter in the limiter circuit. This IC can be powered from the ±8 V supply voltages of the limiter. The limiter board has a 6-way connector (K5) that provides access to the four counter outputs and the sup-ply voltages. Connector K1 of the indicator circuit can be connected to K5 on the limiter board.

 Indicator for Dynamic Limiter Schematic

One output of the 4514 goes high for each unique 4-bit combination on its inputs, while the other outputs remain logic Low. A separate current-limiting resistor is connected in series with each LED. It was not possible to use a common cathode resistor here because most LEDs have a maximum reverse blocking voltage of only 5 V, while the supply voltage here (16 V) is a good deal higher.

The 16 LEDs ar ranged in a r ow pr ov ide a ‘fluid’ indication of the control process. You can enhance the display by using different colours for the first and last LEDs, such as red for D1 (maximum gain) and green for D16 (minimum gain), with yellow for the rest of the LEDs. While observing signals from various sources (TV set, DVD, media player, etc.), you can easily use the 16 LEDS to monitor the behaviour of the limiter and adjust the setting of potentiometer P1 in the limiter circuit. It must be set such that D16 only lights up at the maximum signal level. If this is not possible and D16 remains lit a good deal of the time regardless of the position of P1, it will be necessar y to increase the value of P1. Of course, it is also poss-ible to adjust P1 so the strongest signal source extends slightly above the control range of the limiter.

This circuit can easily be assembled on a small piece of prototyping board. The current consumption is around 4 mA.

Read More

Temperature Indicator Circuit Diagram

This t sink in high power circuits. In this temperature indicator, diode voltage drop in ambient temperature is used as reference level. Temperature is measured by a transistor mounted on a radiator or near power transistor controlled.T1 temperature sensor and voltage to the base - emitter is compared, through potentiometer P1, with the common point of reference in its D1 and R1.

Transistor remains blocked as long as temperature remains below a certain level, which is set to P1. Base-emitter voltage of transistor will decrease by about 2mV for a temperature increase of about 1 ° C. When the emitter voltage of transistor voltage falls below the cursor P1, the transistor will go into conduction and D2 will light.The values of R1 and R2 are voltage dependence of Ub and relationships can be calculated:
R1 = [(Ub - 0.6) / 5] k, R2 = [(Ub - 1.5) / 15] k

Read More

Water Level Indicator Circuit Diagram

The whole project was developed on a friend's request. Its purpose was to remotely monitor the water-level in a metal tank located in the attic by means of a very simple control unit placed in the kitchen, some floors below.


Mains requirements were:

1. No separate supply for the remote circuit
2. Main and remote units connected by a thin two-wire cable
3. Simple LED display for the main unit
4. Battery operation to avoid problems related to mains supply and water proximity
5. As the circuit was battery operated a low current consumption was obviously welcomed

The very small remote unit is placed near the tank and measures the water level in three ranges by means of two steel rods. Each range will cover one third of the tank capacity:

Almost empty - signaled by means of a red LED (D3) in the control unit display
About half-level - signaled by means of a yellow LED (D2) in the control unit display
Almost full - signaled by means of a green LED (D1) in the control unit display

Circuit diagram:

Water-level Indicator Circuit Diagram

Circuit operation:

When the water-level is below the steel rods, no contact is occurring from the metal can and the rods, which are supported by a small insulated (wooden) board. The small circuit built around IC1 draws no current and therefore no voltage drop is generated across R5. IC2A, IC2B and Q1 are wired as a window comparator and, as there is zero voltage at input pins #2 and #5, D3 will illuminate. When the water comes in contact with the first rod, pin #13 of IC1 will go high, as its input pins #9 to #12 were shorted to negative by means of the water contact.

Therefore, R4 will be connected across the full supply voltage and the remote circuit will draw a current of about 9mA. This current will cause a voltage drop of about 0.9V across R5 and the window comparator will detect this voltage and will change its state, switching off D3 and illuminating D2. When the water will reach the second rod, also pin #1 of IC1 will go high for the same reason explained above. Now either R3 and R4 will be connected across the full supply voltage and the total current drawing of the remote circuit will be about 18mA.

The voltage drop across R5 will be now about 1.8V and the window comparator will switch off D2 and will drive D1. The battery will last very long because the circuit will be mostly in the off state. Current is needed only for a few seconds when P1 is pushed to check the water-level and one of the LEDs illuminates.

Parts:

R1 = 15K 1/4W Resistors
R2 = 15K 1/4W Resistors
R3 = 1K 1/4W Resistors
R4 = 1K 1/4W Resistors
R5 = 100R 1/4W Resistor
R6 = 47K 1/4W Resistor
R7 = 3.3K 1/4W Resistors
R8 = 3.3K 1/4W Resistors
R9 = 2.7K 1/4W Resistors
R10 = 15K 1/4W Resistors
R12 = 15K 1/4W Resistors
R13 = 3.3K 1/4W Resistors
R14 = 2.7K 1/4W Resistors
R15 = 2.7K 1/4W Resistors
D1 = 3mm Green LED
D2 = 3mm Yellow LED
D3 = 3mm Red LED
C1 = 470nF 63V Polyester or Ceramic Capacitor
J1 = Two ways output sockets
J2 = Two ways output sockets
P1 = SPST pushbutton
B1 = 9V PP3 Battery
Q1 = BC547 45V 100mA NPN Transistor
IC1 = 4012 Dual 4 input NAND gate IC
IC2 = LM393 Dual Comparator IC
Two steel rods of appropriate length

Read More

Low-Cost Stereo Level Indicator Circuit Diagram

Usually, Low-Cost Stereo Level Indicator home stereo power amplifiers don’t have output level indicators. An output power level indicator can be added to each channel of these stereo power amplifiers. As low levels of the output power are not disturbing and damaging to the people, there is no need to add a preamplifier and low-level detector before IC LM3915. But you should know when the output power becomes considerably high.

Here we present a very simple, low-cost stereo-level indicator circuit for home power amplifiers with power rating of around 0.5W. The circuit is built around two LM3915 dot/bar display driver ICs (IC1 and IC2). LM3915 senses analogue voltage levels to drive ten LEDs, providing a logarithmic 3dB/step analogue display.

Stereo Level Indicator Circuit Diagram

The voltage levels below 1V are not important because these correspond to a low level of the audio signal. Similarly, input voltage levels above 30V correspond to too high levels of the output power, which are not applicable for home power amplifiers. So the voltage levels of our interest are 1V to 30V, which can be handled directly with LM3915. LM3915 needs no protection against ±35V inputs, which simplifies the circuit.

Most audio power amplifiers can drive 2-ohm to around 32-ohm loads. A load of several kilo-ohms will not change the conditions for the amplifier. CON1 is the input connector and CON2 output connector for the loudspeaker or headphone. Each channel has its own LM3915 and ten LEDs to indicate the power level. To indicate the different audio levels, select LEDs of three colours as per your liking. For example, you can have five green LEDs, three yellow LEDs and two red LEDs.

If appropriate signal generators and measuring equipment are not available, the level indicator can be calibrated based on personal observations. For example, the audio signal should be in the green LEDs zone when the signal is strong enough but not irritating, in the yellow zone when it is disturbing or starting to get distorted, and in the red zone when it is heavily distorted or too strong to listen to in the room.

Calibration can be done with the help of potentiometers VR1 and VR2, which are optional. Switches S1 and S2 let you select between two modes of LM3915 operation—the bar mode and the dot mode. These too can be removed or replaced with jumpers, if not required. When the switches are removed, leave pins 9 of IC1 and IC2 open.

The circuit works off regulated 12V. You can also power it through a 12V rechargeable battery.

Assemble the circuit on a general-purpose PCB and enclose in a suitable cabinet. Fix all the LEDs in two rows on the front side of the cabinet. Also affix the two terminals for input and output on rear side of the cabinet. 

Read More

Radiator Temperature Iindicator Circuit Diagram

This radiator temperature indicator can be designed using electronic circuit diagram bellow .Temperature indicator consists of two special zener diode, D1 and D2, connected in series to ensure accuracy of 5.96 V Zener voltage at 25 ° C. As long as the radiator temperature not exceeding 50 ° C, thermal indicator will flash a green LED, one orange will be provided for temperatures of 50 ... 75 ° C and a red LED, for temperatures above 75 ° C.

Zener voltage will increase by 20 mV for each temperature increase of a degree Celsius temperature. Radiator temperature corresponding voltage level is compared with two reference voltages, IC1 and IC2 using. When the temperature reaches 50 ° C, IC2's output goes to logic state "1" so that T3 leads and following ignition with diode D4. At 75 ° C, IC1's output is in logic state "1" and, therefore, T2 and T3 will, so that D3 and D4 lights are off. 

Read More

Dimmable Low Battery Indicator Circuit Diagram

The circuit of battery indicator consists of a 741 operational amplifier configured as a voltage comparator, using a zener diode as a reference voltage pattern. This circuit can be adapted to work with battery between 6 and 18 V, and the only changes required would be a lower Zener voltage and current limit resistor in the case of low voltage below 9 V and greater for higher voltages.The adjustment is made with R2 which can be a trim pot.

Dimmable Low Battery Indicator Circuit Diagram

Read More

Indicator light using Windows Comparison Circuit Diagram

This circuit indicator light level using operational amplifier, LDR and indiction is by LEDs. There are a variety of LDR, its resistance varies from less than 100 ohms on a cloudy day in more than one megohm in complete darkness. A trimmer 2K was used to adjust the range of comparison. This configuration can also be used to indicate  the reconnoiter.

 Indicator light using Windows Comparison Circuit Diagram

Read More

Indicator Consumption AC Load Circuit Diagram

This is Indicator consumption AC Load Circuit Diagram. Some types of electronic equipment does not show that in fact they are consuming energy when they are plugged into an outlet. This pilot light is not required if the unit consumes less than 10 watts according to international standards. But if you turn off the equipment, will be contributing with nature and your pocket, reducing the bill. One way to detect the AC power being consumed, independent of the load is connected in series with a diode AC power supply. In this circuit 6A diodes have been used which can withstand a peak current of 200A is not repeated.

Indicator consumption AC Load Circuit Diagram

The voltage between the diodes serves as the voltage supply for the LED and circuit. To increase the sensitivity of the circuit, we used a voltage doubler consisting of C1, D7, D8 and C2 is used to double the voltage of D1-D6. Another advantage of this scheme is that both reduce by half waves of alternating current. Must use Schottky diodes in a cascade circuit, to minimize voltage losses. 

The LED will light intermittently (flashing) it is connected to a circuit monoastavel by increasing the amount of current flowing through the LED is on, even with small loads. The average consumption is approximately 0.5 mA at a voltage of 3 V (2.7 mA when the LED is on and when it is off 0.2 mA). C4 and R4 determines the time that the LED will blink (0.5-0.6 s, depending on the voltage supply). The light emitting diode (LED) has its off time, which is determined by the C3 and R3 is slightly less than 5 seconds. 

 In D1-D6 measurements indicate that the voltage drop across each diode is about 0.4 V at a current of 1 mA. Must be careful, the circuit is energized and can generate shock, never work in the circuit with the cable connected to the network. The best case for the circuit is a small clear plastic box with the same color of the LED.

Read More

Low-drop Regulator with Indicator Circuit Diagram

Even today much logic is still powered from 5 volts and it then seems obvious to power the circuit using a standard regulator from a rectangular 9-V battery. A disadvantage of this approach is that the capacity of a 9-V battery is rather low and the price is rather high. Even the NiMH revolution, which has resulted in considerably higher capacities of (pen-light) batteries, seems to have escaped the 9-V battery generation. It would be cheaper if 5 volts could be derived from 6 volts, for example. That would be 4 ‘normal’ cells or 5 NiMH- cells. Also the ‘old fashioned’ sealed lead- acid battery would be appropriate, or two lithium cells.

 

Circuit diagram : 

Low-drop Regulator with Indicator Circuit Diagram

 

Using an LP2951, such a power supply is easily realised. The LP2951 is an ever- green from National Semiconductor, which you will have encountered in numerous  Elektor Electronics designs already. This IC can deliver a maximum current of 100 mA at an input voltage of greater than 5.4 V. In addition to this particular version, there are also versions available for 3.3 and 3 V output, as well as an adjustable version.  In this design we have added a battery indicator, which also protects the battery from too deep a discharge. As soon as the IC has a problem with too low an input voltage, the ERROR output will go low and the regulator is turned off via IC2d, until a manual restart is provided with the RESET pushbutton.

 

The battery voltage is divided with a few resistors and compared with the reference voltage (1.23 V) of the regulator IC. To adapt the indicator for different voltages you only need to change the 100-k resistor. The comparator is an LP339. This is an energy-friendly version of the LM339. The LP339 consumes only 60 µA and can sink 30 mA at its output. You can also use the LM339, if you happen to have one around, but the current consumption in that case is 14 times higher (which, for that matter, is still less than 1 mA).

 

Finally, the LP2951 in the idle state, consumes about 100 µA and depend- ing on the output current to be deliv- ered, a little more. 

Sourced by: Streampowers

Read More

Yes-No Indicator Has Zero Standby Current Circuit Diagram

This is the Yes-No Indicator Has Zero Standby Current Circuit Diagram. This circuit produces a random "Yes" or "No" with a single button press - indicated by the illumination of a red or green LED. The circuit has two advantages over similar circuits. First, it uses just a single momentary contact pushbutton, so no on-off switch is required. When the pushbutton is pressed, an oscillator comprising the 10nF capacitor and 22kΩ resistor at pins 1 & 2 is almost immediately stopped by FET Q1, which pulls the oscillator's timing capacitor to the positive rail. However, the 220nF capacitor and 470kΩ resistor in the gate circuit of Q1 introduce a tenth of a second's delay, so that about 250 oscillations take place before the clock is stopped.

Due to variations in charge on the circuit's capacitors, as well as voltage and temperature variations, and the unpredictability of when the pushbutton will be pressed, randomness is assured. The circuit has a high degree of randomness because it takes advantage of a near-perfect complementary square waveform at pins 10 and 11 of the 4047 IC. The oscillator frequency (available at pin 13) is passed through an internal divide-by-2 circuit in the 4047. This appears at pin 10 (Q), and is inverted at pin 11 (Q-bar), thus assuring a near perfect 50:50 duty cycle for the two LEDs.

Yes-No Indicator Has Zero Standby Current Circuit Diagram

Yes-No Indicator Circuit Diagram

Note:
However, that the "impartiality" of the circuit is partly contingent on the value of the 10nF capacitor and on a reasonably equal current flow through both LEDs. Over five trials, the Yes-No Indicator scored 142 Yes, 158 No, with Yes falling behind No in the fourth trial. Because the circuit only works while switch S1 is pressed, standby current is zero, therefore a miniature 12V battery may be used to power it. In this case the circuit could be used thousands of times before the battery would run flat. The circuit has a further potential use. If the LEDs are omitted and a piezo (capacitive) sounder is wired directly to pins 10 and 11, it will produce a loud beep when equipment is turned on, and will continue to draw less than 0.5mA until it is switched off. The frequency of the beep may be changed by altering the value of the 10nF capacitor and its duration by altering the value of the 220nF capacitor.

Author: Thomas Scarborough - Copyright: Silicon Chip Electronics

Read More

Bridge-Rectifier LED Indicator Circuit Diagram

Bridge-Rectifier  LED Indicator Circuit Diagram. Using a few diodes and a LED, you can make a nice indicator as shown in associated schematic diagram that can be used for a lot of applications (with a bit of luck). It’s quite suitable for use in series with a doorbell or thermostat (but don’t try to use it with an electronically con-trolled central-heating boiler!). This approach allows you to make an attractive indicator for just a few pennies.

The AC or DC current through the circuit causes a voltage drop across the diodes that is just enough to light the LED. As the voltage is a bit on the low side, old-fashioned red LEDs are the most suitable for this purpose. Yellow and green LEDs require a somewhat higher forward voltage, so you’ll have to first check whether it works with them. Blue and white LEDs are not suitable. You also don’t have to use modern high-efficiency types (sometimes called ‘2-mA LEDs’ or ‘3-mA LEDs’). If a DC current flows through the circuit and the LED doesn’t light up, reverse the plus and minus leads.

Bridge-Rectifier LED Indicator Circuit diagram :

Bridge-Rectifier  LED Indicator Circuit Diagram

When building the circuit, you’ll notice that despite its simplicity it involves fitting quite a few components to a

small printed circuit board or a bit of prototyping board. That’s why we’d like to give you the tip of using a bridge rectifier, since that allows everything to be made much more compact, smaller and more tidy, and it eliminates the need for a circuit board to hold the components. Besides that, you can surprise friend and foe alike, because even an old hand in the trade won’t understand the trick at first glance and will likely mumble something like “Huh?

That’s impossible.”

A bridge rectifier contains four diodes, which is exactly what you need. If you short the + and – terminals of the bridge, you create a circuit with two pairs of diodes connected in parallel with oppo-site polarity. Select a bridge rectifier that can handle the current that will flow through it. In the case of a doorbell, for example, that can easily be 1 A. Select a voltage of 40 or 80 V.

Never use this circuit in combination with mains voltage, due to the risk of contact with a live lead. 

Read More

Project of Remote Audio Level Indicator Circuit Diagram

Remote Audio Level Indicator Circuit Diagram. The normal level-indicator circuits which are available in the market require connections to be made to the output of the player, which may not be easily accessible. The audio level indicator circuit described here removes this restriction as it may be placed close to the player’s speakers and yet the desired effect can be realized.

Remote Audio Level Indicator Circuit Diagram :

Remote Audio Level Indicator Circuit Diagram

As shown in the circuit, signals are picked up by the condenser microphone, which get further amplified by the noninverting amplifier built around one of the four op-amps of LM324. The remaining three, along with four op-amps of the second LM324, are used as seven comparators to work as the level detector, giving seven output levels through seven coloured LEDs. 

The sensitivity of the audio level indicator circuit may be improved by varying the 220k potentiometer. If a fine adjustment is desired, a 4.7-kilohm potentiometer may be connected in series resistors with the 220k potentiometer.

Copyright : EFY

Read More