Coil Energy Saver Circuit Diagram

 Coil Energy Saver Circuit Diagram. Some relays will become warm if they remain energized for some time. The circuit shown here will actuate the relay as before but then reduce the ‘hold’ current through the relay coil current by about 50%, thus considerably reducing the amount of heat dissipation and wasted power. The circuit is only suitable for relays that remain on for long periods. The following equations will enable the circuit to be dimensioned for the relay on hand: R3 = 0.7 / I Charge time = 0.5 × R2 × C1 

 Coil Energy Saver Circuit Diagram

 Coil Energy Saver Circuit Diagram


Where I is the relay coil current. After the relay has been switched off, a short delay should be allowed for the relay current to return to maximum so the relay can be energized again at full power. To make the delay as short as possible, keep C1 as small as possible. In practice, a minimum delay of about 5 seconds should be allowed but this is open to experimentation.

The action of C2 causes the full supply voltage to appear briefly across the relay coil, which helps to activate the relay as fast as possible. Via T2, a delay network consisting of C1 and R2 controls the relay coil current flowing through T1 and R3, effectively reducing it to half the ‘pull in’ current. Diode D2 discharges C1 when the control voltage is Low. Around one second will be needed to completely discharge C1. T2 shunts the bias current of T1 when the delay has elapsed. Diode D1 helps to discharge C1 as quickly as possible. The relay shown in the circuit was specified at 12 V / 400 ohms. All component values for guidance only.



Author: Myo Min - Copyright: Elektor July-August 2004
Read More

Electronic Fuse Employs A Relay Circuit Diagram

chile many power supplies can be set to limit their output current to a defined level, to protect the circuit they are powering, no such protection is available if you are powering a circuit from a battery. If a fault develops, the circuit can blow before you have a chance to disconnect it. Of course, you can fit a fuse in series with the supply line to the circuit under test but it will blow if a fault develops. Or perhaps it won’t blow sufficiently quickly to protect the circuit. And repeatedly having to replace fuses becomes a nuisance as well.

Electronic Fuse Employs A Relay Circuit Diagram


Electronic Fuse Employs A Relay

The alternative is to use an electronic fuse. This circuit uses a relay to make and break the circuit. The current drain of the circuit under test is monitored by a 1O 2W resistor which is placed in series with the supply line. The voltage across this 1O resistor is monitored by op amp IC1a which has an adjustable gain of between 11 and 16, as set by trimpot VR1. The resultant DC voltage from pin 1 of IC1a is fed to pin 5 of IC1b which is configured as a comparator. Trimpot VR2 provides an adjustable voltage reference to pin 6 of IC1b and this is compared with the amplified signal from IC1a.

If IC1b’s threshold is exceeded, its pin 7 goes high and this is fed to Schmitt trigger inverter IC2a which then “sets” the RS flipflop comprising gates IC2c & IC2d. Pin 11 of IC2d then goes high to turn on transistor Q2 and LED1 while pin 4 of IC2b also goes high to turn on Q1 and the relay which then disconnects the load. The circuit stays in this state until the RS flipflop is reset by pushing switch S1. Capacitor Cx, across the feedback resistance of IC1a, is used to simulate a slow-blow or fast-blow fuse and can be selected by trial and error. Changing the gain of IC1a or the value of the sensing resistor changes the fuse rating of the circuit.
Read More

Relay Step-Up Circuit Diagram

Have you ever needed to power a 12-volt relay in a circuit but only had 6 or 9 volts available? This simple circuit will solve that problem. It allows 12-volt relays to be operated from 6 or 9 volts, or 24-volt relays from 12 volts. While most normal relays require the manufacturer-specified coil voltage to reliably pull the contacts together, once the contacts are together you only need about half that rated voltage to hold them in. This circuit works by using that principle to provide a short burst of twice the supply voltage to move the contacts and then applies the available 6 or 9 volts to the relay to lock the contacts in place.
With reference to Figure A., when the main supply is applied to the circuit the 220-µF capacitor, C1, charges quickly to +6 volts through resistor R3. The circuit is now awaiting voltage on the control input. When a control voltage (can be as little as 3 volts) is applied to the control input, transistor T1 switches on. The other transistor, a BC558, is also switched on. This allows connection of the relay coil to the main supply rail while T1 shorts the positive terminal of the 220-µF capacitor to ground. Now the negative terminal of the capacitor is at a potential of –6 volts. This is applied to the other side of the relay coil. The relay coil potential is then briefly 12 volts — enough to actuate the contact(s).
However, the coil voltage drops to the supply voltage fairly quickly. The period is determined by the R-C time constant of the relay coil resistance and the 220-µF capacitor. While this circuit is simple and works well in many situations, it has a few weaknesses in its current form. The relay may remain energized for as long as one second after the control input has fallen. Also, if the control input goes high before the capacitor has fully recharged, it may not have enough energy to control the relay reliably. Also, the voltage drop across the diode limits the voltage to about 10.8 volts.

The more complex version of the circuit shown in Figure B fixes these problems by using an extra transistor and diode. In this arrangement, the BC558 is now isolated from the recharge current of the capacitor. The new transistor provides fast charging for the capacitor. Charging is completed within the mechanical response time of the relay. When using these circuits it should be noted that the contact pressure of the relay contacts may be al little lower than with the nominal coil voltage. It is therefore advisable to keep contact currents well below the maximum specified value. 
Read More

Solid State Relay - Required Only 50uA Drive Current

This circuit demands a control current that is 100 times smaller than that needed by a typical optically isolated solid state relays. It is ideal for battery-powered systems. Using a combination of a high current TRIAC and a very sensitive low current SCR, the circuit can control about 600 watts of power to load while providing full isolation and transient protection.



Read More

Relay Toggle Switch Circuit Diagram

Half of RL1 and RL2 manipulate the switching and the other is connected to an application. Relays are 200 ohms above ground and at one point are referenced to positive that turns them off.

Description:

RL1 (which is off) applies plus voltage from its armature and latches RL2 “on”. The application terminals are set to [A]. The condition changes when S1 is activated, voltage is applied to RL2 latching RL1 “on” releasing S1 turns RL2 “off”. RL2’s armature is then directed to R1. Terminals are set to [B].

When S1 is pressed again, the relays negative side are referenced to positive, RL1 turns “off” (there’s no current flow). RL2 turns “on” when S1 is released, terminals are set to [A]. There is slight lag between relays depending on how long S1 is held.

Relay Toggle Switch Circuit Diagram

Note: 

If different relays are used, adjustment of R1’s value may be required. For example, OEG relays (12vdc, 270 ohm coil) need R1 at 60 - 70 ohms. The prime motivation for this design was to avoid using toggle switches for my audio control panel. Another plus, it can be controlled from a remote transmitted pulse.Link
Read More

Relay activated by Sound Circuit Diagram

This is a Relay activated by Sound Circuit Diagram. Generally a circuit has a basic function, but according to our needs can modify or add to a circuit making it more complex. This circuit is a relay activated by sound, which can be used in an alarm system, home automation, robot and even in an Arduino. Undoubtedly this control by sound can be very useful, an example is a light activated by the sound of a knock on the door or a round of applause.

The light turns off automatically after a few seconds. An alternative is to use protection against theft - if someone wants to open the door or break something light illuminates, indicating that someone is home. The circuit can work with any voltage 5-12 Vdc, it depends on the voltage of the relay coil.

Relay activated by Sound Circuit Diagram

Relay activated by Sound Circuit Diagram

Read More

Relay Switch Activated by Tone and Signal

This is a simple project of Relay Switch Activated by Tone and Signal circuit diagram.The essence of the circuit is for the input of tone and signal to provide an activation for the relay switch.
  • Relay – an electrically operated switch where the current flowing through the coil of the relay is creating a magnetic field which attracts a lever and changes the switch contacts, thereby making its state open or close
  • BC214 – a complementary silicon planar epitaxial transistor used in AF small signal drivers and am1 as well as for low noise preamplifier applications due to its feature of good linearity of DC current gain
  • LM741 – a general purpose single operational amplifier with features such as offset null, compensated internal freq uency, voltage range with high input, good stability of temperature, and protected from short circuit
The use of relay will allow the circuit to switch from one condition to another. It can also be referred to as a form of an electrical amplifier since it is able to control an output circuit of higher power than the input circuit. There are many types of relays being used in many electronic and electrical circuits, which include solid-state relay, Buchholz relay, overload protection relay, latching relay, forced-guided contacts relay, mercury-wetted relay, contactor relay, machine tool relay, reed relay, polarized relay, and solid state contactor relay.
Build a Relay Switch Activated by Tone and Signal
The circuit created is sensitive enough to the AC signals in the input stage, where the signals are ranging above 5 mV. It will also be sensitive to react with the human voice signals having a range of frequency from 50 Hz up to 3 KHz. The human voice is a part of the human sound produced primarily by the vocal cords or vocal folds which in turn produces a voice frequency that is used for the transmission of speech.

During the absence of an input signal, the state of the 12 V relay RL1 is at OFF condition as regulated by the 10K Ohms trimmer RV1. The circuit can be made to react with its sensitivity in points A, B, & C, where a negative feedback can be placed due to the addition of band pass filter. The filter will operate only in the 1 KHz range and the circuit will only correspond at this frequency.
Relay Switch Activated by Tone and Signal

The signal and tone activated relay switch were used in a wide range of fields which includes measuring instruments, audio systems, communications equipment, and factory-automation equipment. They can also be found on telephone subscriber circuits for the polarity reversing switch, testing, and ringing functions. Source
Read More

Water Pump Relay Controller Circuit Diagram

Water reservoir automatic level control, Simple circuitry - 12V supply By means of a Relay, employed to drive a water pump, this circuit provides automatic level control of a water reservoir or well. The shorter steel rod is the "water high" sensor, whereas the longer is the "water low" sensor. When the water level is below both sensors, IC1C output (pin #10) is low; if the water becomes in contact with the longer sensor the output remains low until the shorter sensor is reached. At this point IC1C output goes high, Q1 conducts, the Relay is energized and the pump starts operating.

Now, the water level begins to decrease and the shorter sensor will be no longer in contact with the water, but IC1C output will be hold high by the signal return to pin #5 of IC1B, so the pump will continue its operation. But when the water level falls below the longer sensor, IC1C output goes low and the pump will stop. SW1 is optional and was added to provide reverse operation. Switching SW1 in order to connect R3 to pin #11 of IC1D, the pump will operate when the reservoir is nearly empty and will stop when the reservoir is full. In this case, the pump will be used to fill the reservoir and not to empty it as in the default operating mode.

Water Pump Relay Controller Circuit diagram:

 Water Pump Relay Control Circuit Diagram

Parts:
R1 = 15K - 1/4W Resistors
R2 = 15K - 1/4W Resistors
R3 = 10K - 1/4W Resistor
R4 = 1K - 1/4W Resistor
D1 = LED - any type and color
D2 = 1N4148 - 75V 150mA Diode
Q1 = BC337 - 45V 800mA NPN Transistor
IC1 = 4001 Quad 2 Input NOR Gate CMos IC
SW = SPDT Toggle or Slide Switch (Optional)
RL1 = Relay with SPDT 2A @ 230V switch
Coil Voltage 12V - Coil resistance 200-300 Ohm
Two steel rods of appropriate length

Notes:
  • The two steel rods must be supported by a small insulated (wooden or plastic) board.
  • The circuit can be used also with non-metal tanks, provided a third steel rod having about the same height of the tank will be added and connected to the circuit's negative ground.

Read More

Low Voltage Cut-Out

Low Voltage Cut-Out Circuit diagram. This circuit will detect when the voltage of a 12v battery reaches a low level. This is to prevent deep-discharge or maybe to prevent a vehicle battery becoming discharged  to a point where it will not start a vehicle. This circuit is different to anything previously presented. It has HYSTERESIS. Hysteresis is a feature where the upper and lower detection-points are separated by a gap. 

Low Voltage Cut-Out Circuit diagram :

 
Low-Voltage-Cut-Out Circuit-Diagram
Low Voltage Cut-Out Circuit Diagram

Normally,  the circuit will deactivate the relay when the voltage is 10v and when the load is removed. The battery voltage will rise slightly by as little as 50mV and turn the circuit ON again. This is called "Hunting." The off/on timing has been reduced by adding the 100u. But to prevent this totally from occurring, a 10R to 47R is placed in the emitter lead. The circuit will turn off at 10v but will not turn back on until 10.6v when a 33R is in the emitter. The value of this resistor and the turn-on and turn-off voltages will also depend on the resistance of the relay. 


Author : Colin Michel - Copyright : 200 Transistor Circuits
Read More

Simple Relay Driver Circuit Diagram

This is a Simple Relay Driver Circuit Diagram. This device is used to switch inductive loads such as relays, solenoids incandescent lamps, and small DC motors without the need of a free-wheeling diode.The relay operates a certain time, td, after power is applied to it, and then it operates for a length of time, tc. The SCR fires when the voltage on Ci reaches VA. 

 Simple Relay Driver Circuit Diagram


Simple Relay Driver Circuit Diagram


This operates the relay, which stays activated until the current charging C2 drops below the dropout current. To keep the relay in its activated position indefinitely (tc =00), eliminate C2 and choose R2 just large enough to keep the relay coil current within its related limits. 


Typical component values
 td = 30 seconds and tc = 2 seconds 
are
Rl = 1.5 megohms, 
R2 = 10 k ohms, 
R3 = 3 k ohms, 
Cl = 47 µ¥, and 
C2 = 100 µ¥. 
The SCR is a 2N1877 and the relay is a Potter Brumfield PW-5374. A value of 12 Vdc is assumed for V~.
Read More